Gokul Traders

• Non waterproof
• Resolution : 0.01mm/0.0005*
• Buttons : zero, mm/inch, on/off
• After power off, move the digital unit to turn on power
• Battery CR2032
• Data Output
• Meet DIN862
• Made of stainless steel
• Optional accesory: data output system
• Supplied with manufaturer calibration certificate

• Protection level IP65 against dust & water (coolant proof)
• Stainless steel spindle to avoid rust
• Carbide measuring faces
• mm / inch conversion
• Auto power off
• SR44/LR44 battery
• Ball attachment free of cost
• Absolute & incremental measuring mode
• Easy operations with 2 buttons
• USB compatible data output interface
• Can be connected to PC through SPC cable P1502 and data can be transferred by switch P1601
• Each micrometer is supplied with calibration certificate stating actual values
• Supplied in attractive sturdy box
• Real value for money

Solid carbide end mills available in 1 / 2 / 4 flute with straight or spiral form. Coated uncoated.
We can give  Rohit , Totem make

Hss hand taps are straight flute general purpose taps which can be used for both machine or hand tapping. They are generally the most economical tool for use on production runs, but are best on materials that produce chips, or where the swarf breaks readily. Where deep holes are to be tapped, in materials which produce stringy swarf, other types of taps may be needed, especially for coarse threads. Hand taps can be supplied in sets of three; bottom, second and taper leads, or individually.

• Bottom Taps have a chamfer (lead) of 1–2 threads, the angle of the lead being around 18 degrees per side. They are used to produce threads close to the bottom of blind holes.
• Second Taps have a lead of 3-5 threads at 8 degrees per side. They are the most popular and can be used for through holes, or blind holes where the thread does not need to go right to the bottom.
• Taper Taps have a lead of 7-10 threads at 5 degrees per side. The taper lead distributes the cutting force over a large area, and the taper shape helps the thread to start. They can therefore be used to start a thread prior to use of second or bottom leads, or for through holes

Description:

• AISI M2 grade Square HSS Tool bits or Lathe Tool bits manufactured since 1963,
• Hardness of these M2 tool bits (ROHIT 1X) ranges from 62~65HRc,
• Tool bits manufactured starting from 1/16" to 2" Square in all lengths.
• All grades of Tool Bits or Lathe Bits namely M2, M35, M42, T42, ASP are manufactured at RIGPL

Description:

• HSS Drill blanks or Round HSS Tools Bits are manufactured in HSS M2 grade
• Hardness ranges for these HSS Tool Bits from 62~65HRc
• HSS Drill blanks or HSS Round Tool Bits are manufactured with 0* Bevel Angle and h10 tolerance
• Special sizes & bevel angles are manufactured as per customer needs
• At RIGPL, HSS Cutting Tools are also manufactured in all grades M2, M35, M42, T42, ASP grades

Description:

• AISI M2 grade HSS Flat / Rectangular Tool bits are manufactured since 1963,
• Hardness of these M2 flat tool bits (ROHIT 1X) ranges from 62~65HRc,
• Following grades of Flat Tool Bits are stocked in M2, M35, T42 grades by Rohit Cutting Tools,
• Special Sizes & Special Grades (like M42, ASP) are also manufactured on requests in HSS Flat Tool Bits.

Spiral pointed tap is also known as ‘gun nose’ or ‘bull nose’ or chipdriver. These taps are dimensionally the same as a hand tap, second lead, but have the cutting face ground back relative to the axis of the tap, for the lead portion. This gives the flute a better cutting action, requiring less power, and pushes the cut material forward, allowing free flow of coolant along the flutes to the cutting edge. The flutes are not ground as deeply as for hand taps, giving the tap greater strength. It can therefore be run at higher speeds. Spiral point taps are ideal for machine tapping of through holes, or blind holes where there is enough clearance beyond the threaded portion to accommodate the swarf.

Advantages:

• Thread Chamfer is of 4.5 threads & cutting load is distributed
• Shallow flute depth, hence stronger tap
• Chip clogging is eliminated as the tap pushes the chip forward and thus enhancing tool life.

We are engaged in offering to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering to our clients. Our range of all products is widely appreciated by our clients.

General Purpose Application ‘Totem’ range of Carbon Alloy Steel taps are known worldwide for their excellent quality. We are one of the largest producer of Carbon Taps around the world. We export more than 50% of our total production. We also do contract manufacturing for some of the very well known and prestigious brands.

Description:

• HSS Parting tools bits or cut-off blades are manufactured in HSS M2 grade
• Hardness ranges for these tool bits from 62~65HRc
• Parting tool bits can be manufactured in FORM E & INDEX Type as per request
• Comes with h13 tolerance
• More than 50+ sizes of Parting Tool bits are in stock to choose from in all grades

Forming Otherwise known as ‘Roll’, ‘Fluteless’ or Polygon taps. Used for the chipless production of threads in ductile materials such as copper, aluminium, soft brass or steel. Threads produced by fluteless taps are formed by plastic deformation, they are not cut. These taps do not have flute or cutting edges but have special roll forming lobes with circular land. They are operated at high speeds and are better at maintaining gauge qualification. Because they produce no chips they are very suitable for blind hole application as well as through hole application.

Forming taps require different tapping drill sizes when compared to drill sizes used for cut taps.

Advantages of Forming taps sd series

• Can run at higher parameters ex. cutting speed
• Better durability compaired to cutting taps
• Sturdy exactness for dimensions & profile
• Better stability for formed threads
• Minimum chance of fracture
• No swarf, thus no concern of its disposable

These taps are used to produce a thread close to the bottom of a blind hole and therefore have a very short lead. The right hand spiral cut of the flutes acts to force the swarf away from the cutting teeth to the rear of the flutes and out of the hole. They are better on materials which form long continuous stringy swarf, rather than chips. They are also better to tap a thread in a hole where there is a break in the material, e.g. another hole, as the spiral fluting helps the tap to pick up on the other side. Spiral flute taps can have slow or fast helix angles.

Advantages: 

• Can be used in both blind holes & also in through holes
• Chips are pushed upwards due to spiral flute – Chip clogging avoided
• Full thread depth can be achieved and this design prevents tap breakage

•  Measure wall thickness of tubes
• Resolution 0.001mm/0.00005″
• IP65 dust/waterproof
• Button function: on/off, set, mm/inch, data transmit
• Data output
• Automatic power off
• Ratchet stop
• Carbide measuring faces
• Supplied with setting standards (except 0-25mm/0-1″)
• Optional accessory: data output cable

All types of HSS cutting tools like drills , taps, spiral flute taps, centre drills , reamers , counterbore, end mill , slot cutter, side and face ctter, centre reamer ,